# Draw a workbench

Draw a workbench by hand with typed sizes, axis locks, copies and the tape measure.

In this tutorial, you draw a workbench 1800 mm long, 600 mm deep and 900 mm high. It has a top of 18 mm plywood and six legs. You learn the drawing tools, the measurements box, axis locks, copies and arrays, and the tape measure.

You need about 20 minutes. Do [Your first bookcase](/docs/tutorials/first-bookcase/) first.

This tutorial uses the UK region with sizes in mm. In other regions, the default sheet and timber have different sizes, so the numbers are different.

## Start a new project

1. Click **File**.
2. Move the pointer to **New**.
3. Click **Furniture design…**.
4. In **Name**, type `Workbench`.
5. Click **Create**.
6. If **Region** in the **Properties** panel does not show **UK**, select **UK**.

![The New project dialog with the name Workbench and the type Furniture design.](/docs/img/tutorials/workbench-new-project.jpg)

The 3D view is empty. The red, green and blue lines are the X, Y and Z axes. The point where they meet is the origin.

## Draw the top

You draw a panel with the **Rectangle** tool. You type the sizes in the measurements box at the bottom right of the window.

1. Press R to select the **Rectangle** tool.
2. Click the origin.
3. Type `1700,600`. The values go into the measurements box.
4. Press Enter.
5. Move the pointer up.
6. Type `18` and press Enter.

![The Rectangle tool with 1700,600 in the measurements box at the bottom right.](/docs/img/tutorials/workbench-top-typing.jpg)

A panel 1700 × 600 × 18 mm is on the ground. The cut list shows one part, **Panel**, in the sheet material of **Sheet (R tool)**.

Give the panel a name:

1. In the **Properties** panel, double-click **Panel** in **Name**.
2. Type `Top` and press Enter.

## Make the top longer with Push/Pull

The top must be 1800 mm long. You push the end face out by 100 mm.

1. Press P to select the **Push/Pull** tool.
2. Move the pointer over the right end face of the top. The face is thin, so zoom in with the mouse wheel if necessary.
3. Type `100` and press Enter.

The top is now 1800 mm long. The cut list shows 1800 in the **L** column.

## Lift the top with an axis lock

The top must sit on legs 882 mm high, so its upper face is at 900 mm. You move it up along the blue Z axis.

1. Press M to select the **Move** tool.
2. Click the top.
3. Move the pointer up.
4. Press Z to lock the movement to the blue axis.
5. Type `882` and press Enter.

![The Move tool with the Z axis locked and 882 in the measurements box.](/docs/img/tutorials/workbench-lift.jpg)

The status bar showed "Z axis locked" before you typed. The top now floats 882 mm above the ground. Press F to fit the view.

## Draw a leg with the Timber tool

The **Timber** tool draws a timber member between two points. It uses the profile in the status bar, for example **C24 regularised KD 45×95**.

1. Press B to select the **Timber** tool.
2. Click the origin.
3. Move the pointer up.
4. Press Z to lock to the blue axis.
5. Type `882` and press Enter.

A leg 882 mm long stands at the origin, below the corner of the top. The line you draw is the centreline of the leg, so the leg is half outside the top.

Move the leg in under the top:

1. Press M to select the **Move** tool.
2. Click the leg.
3. Type `50,50,0` and press Enter.

Three numbers are an exact X, Y and Z offset. The leg moves 50 mm along X and 50 mm along Y.

## Copy the leg in an array

1. With the **Move** tool, click the leg.
2. Press Alt to start a copy. On a Mac, press ⌥.
3. Move the pointer to the right, along the red axis.
4. Press X to lock to the red axis.
5. Type `850` and press Enter.
6. Type `x2` and press Enter.

The status bar shows "2 copies, 850, 0, 0 mm apart". There are now three legs along the front: at each end and in the middle.

![Three legs under the front edge of the top, after the copy and the x2 array. All three legs are selected.](/docs/img/tutorials/workbench-array.jpg)

## Copy the legs to the back

After the array, KerfCraft selects all three legs: the first leg and the two copies. The **Move** tool is still active.

1. Click one of the selected legs.
2. Press Alt (on a Mac, ⌥) to start a copy.
3. Move the pointer towards the back, then press Y to lock to the green axis.
4. Type `500` and press Enter.
5. Press Space to select the **Select** tool.
6. Press Esc to clear the selection.

The workbench has six legs. The cut list shows **Top** and 6 legs of the same length.

## Measure with the tape measure

1. Press T to select the **Measure** tool.
2. Click the front bottom corner on the right side of the first leg.
3. Click the front bottom corner on the left side of the middle leg.

The tape shows the clear distance between the two legs, 805 mm with 45 mm legs. The status bar also shows Δx, Δy and Δz. Press Esc to clear the tape.

![The tape measure between two legs, showing 805 mm.](/docs/img/tutorials/workbench-tape.jpg)

## Examine the cut list

1. Click the **Cut list** tab.
2. Read the two rows: the top and the 6 legs.

Check every dimension against your own measurements before cutting. This workbench has no rails or bracing. Before you build a real bench, add the parts that make it stiff.

## What you learned

- You type sizes in the measurements box while a tool is active.
- X, Y and Z lock a movement to one axis.
- Alt (⌥ on a Mac) copies with the **Move** tool, and `x2` after a copy makes an array.
- The tape measure shows distances between points on the model.

Next, put furniture in a room in [Put a wardrobe in a room](/docs/tutorials/wardrobe-in-a-room/). For every tool key, see [Keyboard shortcuts](/docs/reference/keyboard-shortcuts/).